Republic Lagun | American Turnmaster ATV 916-TM

American Turnmaster ATV 916-TMUltra Hi-Precision Lathe

OUTSTANDING FEATURES

Designed to machine precision small diameter parts
Guaranteed circular accuracy to 50 millionths of an inch
5 HP Electronic Variable Speed (EVS) with RPM Digital display and quick-change hi-lo lever.
Spindle is mounted in high precision pre-loaded angular contact ball bearings eliminating radial and end play.
Solid hardened and ground tool steel bed
Cross and compound slide with hardened and ground screws
Ball bearing precision 5C lever type collet closer
Solid one-piece cast headstock with outstanding rigidity
Full-bearing tailstock with graduated quill and quick release of tools
Quick-acting tool post slide for threading
Flood coolant pump and piping
Heavy gauge steel pedestal with storage compartment

STANDARD EQUIPMENT

5C lever type collet closer
Compound slide with T-slot
Tailstock
Flood coolant with 12 liter tank capacity
5 HP EVS variable speed drive with direct reading of RPM
Welded steel pedestal cabinet with storage compartment
Low voltage magnetic electric control panel arranged for 3/60/220 VAC operation, with thermal overload protection
Operation manual, parts book, test certificate and service tools
Leveling bolts and pads

SPECIFICATIONS	ATV-916-TM
Swing over bed ways	9” (229 mm)
Center distance	15” (380 mm)
Length of bed	36” (915 mm)
Top slide	4 ¼” (108 mm)
Bottom slide	5 ½” (140 mm)
Spindle speeds, number	Infinitely variable
Spindle speed, range	0~4,000 RPM
Spindle nose, inside taper for 5C/OD	10 degrees / 4 degree taper
3-Jaw chucks	6” (150 mm)
With expanding collets	3” (76 mm)
5C Round collets	1-1/16” (27 mm)
5C Hex collets	7/8” (22 mm)
With square collets	¾” (19 mm)
With step chucks	1-1/16 to 6” (27 to 152 mm)
Spindle taper	MT #2
Spindle diameter	1.35” (34.5 mm)
Spindle travel	3 ¾” (95 mm)
Main drive motor, 220V	5 HP EVS (3.7 kW)
Coolant pump motor	1/8 HP (0.9 kW)
Machine net weight	1,000 lbs. (455 kg)

	Face Plate 7” Face Plate
	Collet and Pads Expanding collet and pads
	Holder Releasing tap holder
	Attachment Radius turning attachment
	X-Z Compound Slide The compound slide rest can be readily applied to the American Turnmaster Second Operation Machine for screw feed precision turning, facing and boring operations. The large diameter feed screws are hardened and mounted on preloaded ball bearings. The feed screw dials are 50.8mm in diameter. Both dials give direct readings in thousandths and are adjustable for Zero settings.
	Turning Slide Straight and taper turning slide
	Cut-off Slide Vertical cut-off slide
	Shields Chip and coolant shield
	Acu-Rite 200 Acu-Rite 200-T 2-axis Digital read-out system with 0.00005” 6” cross feed scale, 0.0001” 20” longitudinal scale, mounting brackets, console tray, and featuring: Tool offset library(9), radius/diameter conversion, preset and reset, near zero warning, axis lock (hold), linear error compensation, conversational message prompts, absolute/incremental, inch/metric, “Position-Trac” with battery back-up, completely installed
	Quick Change Toolholders Dorian Tool Super Quick Change First time buyers set. - Five piece set with body, assorted tool holders, tools and inserts. - Capacity 1/2”
	Quick Change Toolholders Dorian Tool Quadra First time buyers set. - Five piece set with body, assorted tool holders, tools and inserts. - Capacity 1/2”

Be the first to review! Contact Us [+]