Republic Lagun | Heavy Duty AT-P5T Series

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

One piece (monolithic) bed, floor type casting
Three bedway design, with extra way on front face of base supporting the apron.
All three ways are hardened and ground
Forged steel spindle with opposed taper roller bearings
Dual chucks are optionally available
Hardened and ground gears and shafts throughout
Hardened and ground cross slide ways and screw
Electromagnetic spindle brake
Universal inch / metric gear box, totally enclosed
18 speed geared headstock
Six way rapid traverse and power feed to top slide
Thread chasing dial;
Overload safety device on apron
Dual voltage motor and controls, 30 HP

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

SPECIFICATIONS	TL-45
Swing over bed ways	45” (1135mm)
Swing over cross slide	32” (810mm)
Swing thru gap	65” (1650mm)
Gap length	24” (600mm)
Distance between centers	60” to 480” (1524mm to 12000mm)
Casting type	One piece (monolithic) bed floor type
Bed way design	3 e/a with extra ways supporting apron
Width of bed across ways	28” (711mm) w/o auxiliary guide / 32” (812mm) with auxiliary guide
Spindle Bore, standard	6.02” (153 mm)
Spindle nose, standard	A2-11
Spindle speeds	18
Spindle speed range	18 to 1000 RPM
Main drive motor	30 HP (22.47 kW)
Travel, cross slide	31.50” (800 mm)
Travel, top slide (power)	17.75” (450mm)
Leadscrew diameter/ Pitch	12" (2)
Inch thread range TPI (60)	0.5 ~ 28
Metric thread range TPI (60)	1 ~ 56
Modular thread range TPI (60)	0.25 ~ 14
Longitudinal feed range	0.0018 ~ 0.1 IPR (0.045 ~ 2.55 MPR)
Cross feed range	0.0009 to 0.050 IPR (0.23 to 1.28 MPR)
Rapids, longitudinal	80 IPM (2 MPM)
Rapids, cross	40 IPM (1 MPM)

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

SPECIFICATIONS	TL-50
Swing over bed ways	50.13” (1273mm)
Swing over cross slide	37.38” (950mm)
Swing thru gap	70.50” (1793mm)
Gap length	24” (600mm)
Distance between centers	60” to 480” (1524mm to 12000mm)
Casting type	One piece (monolithic) bed floor type
Bed way design	3 e/a with extra ways supporting apron
Width of bed across ways	28” (711mm) w/o auxiliary guide / 32” (812mm) with auxiliary guide
Spindle Bore, standard	6.02” (153 mm)
Spindle nose, standard	A2-11
Spindle speeds	18
Spindle speed range	18 to 1000 RPM
Main drive motor	30 HP (22.47 kW)
Travel, cross slide	31.50” (800 mm)
Travel, top slide (power)	17.75” (450mm)
Leadscrew diameter/ Pitch	12" (2)
Inch thread range TPI (60)	0.5 ~ 28
Metric thread range TPI (60)	1 ~ 56
Modular thread range TPI (60)	0.25 ~ 14
Longitudinal feed range	0.0018 ~ 0.1 IPR (0.045 ~ 2.55 MPR)
Cross feed range	0.0009 to 0.050 IPR (0.23 to 1.28 MPR)
Rapids, longitudinal	80 IPM (2 MPM)
Rapids, cross	40 IPM (1 MPM)

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

SPECIFICATIONS	TL-60
Swing over bed ways	60.13” (1527mm)
Swing over cross slide	47.25” (1201mm)
Swing thru gap	80.25” (2040mm)
Gap length	24” (600mm)
Distance between centers	60” to 480” (1524mm to 12000mm)
Casting type	One piece (monolithic) bed floor type
Bed way design	3 e/a with extra ways supporting apron
Width of bed across ways	28” (711mm) w/o auxiliary guide / 32” (812mm) with auxiliary guide
Spindle Bore, standard	6.02” (153 mm)
Spindle nose, standard	A2-11
Spindle speeds	18
Spindle speed range	18 to 1000 RPM
Main drive motor	30 HP (22.47 kW)
Travel, cross slide	31.50” (800 mm)
Travel, top slide (power)	17.75” (450mm)
Leadscrew diameter/ Pitch	12" (2)
Inch thread range TPI (60)	0.5 ~ 28
Metric thread range TPI (60)	1 ~ 56
Modular thread range TPI (60)	0.25 ~ 14
Longitudinal feed range	0.0018 ~ 0.1 IPR (0.045 ~ 2.55 MPR)
Cross feed range	0.0009 to 0.050 IPR (0.23 to 1.28 MPR)
Rapids, longitudinal	80 IPM (2 MPM)
Rapids, cross	40 IPM (1 MPM)

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

SPECIFICATIONS	TL-70
Swing over bed ways	70.50” (1790mm)
Swing over cross slide	57.38” (1460mm)
Swing thru gap	90.50” (2300mm)
Gap length	24” (600mm)
Distance between centers	60” to 480” (1524mm to 12000mm)
Casting type	One piece (monolithic) bed floor type
Bed way design	3 e/a with extra ways supporting apron
Width of bed across ways	28” (711mm) w/o auxiliary guide / 32” (812mm) with auxiliary guide
Spindle Bore, standard	6.02” (153 mm)
Spindle nose, standard	A2-11
Spindle speeds	18
Spindle speed range	18 to 1000 RPM
Main drive motor	30 HP (22.47 kW)
Travel, cross slide	31.50” (800 mm)
Travel, top slide (power)	17.75” (450mm)
Leadscrew diameter/ Pitch	12" (2)
Inch thread range TPI (60)	0.5 ~ 28
Metric thread range TPI (60)	1 ~ 56
Modular thread range TPI (60)	0.25 ~ 14
Longitudinal feed range	0.0018 ~ 0.1 IPR (0.045 ~ 2.55 MPR)
Cross feed range	0.0009 to 0.050 IPR (0.23 to 1.28 MPR)
Rapids, longitudinal	80 IPM (2 MPM)
Rapids, cross	40 IPM (1 MPM)

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

SPECIFICATIONS	AT-2140-G-TW	AT-2160-G-TW
Swing over bed	21” (533 mm)	21” (533 mm)
Swing over cross slide	14” (356 mm)	14” (356 mm)
Distance between centers	40” (1000mm)	60” (2000mm)
Spindle nose	D1-8	D1-8
Spindle bore(max. bar diameter)	3 1/16” (78.5 mm)	3 1/16” (78.5 mm)
Spindle speed	16 steps	16 steps
Spindle speed range	20 – 1,600 rpm	20 – 1,600 rpm
Ranges:	20-25-35-50-65-85-115-150-210- 280-380-500-670-900-1200-1600	20-25-35-50-65-85-115-150-210- 280-380-500-670-900-1200-1600
Length on bed	21” (537 mm)	21” (537 mm)
Width of bridge	21 3/8” (542 mm)	21 3/8” (542 mm)
Cross slide travel	11” (280 mm)	11” (280 mm)
Top slide travel	5 3/8” (137 mm)	5 3/8” (137 mm)
Number of V ways	3 each “V” ways	3 each “V” ways
Bed width	13 ½” (345 mm)	13 ½” (345 mm)
Swing in gap	31” (790 mm)	31” (790 mm)
Gap bed length from faceplate	8” (200 mm)	8” (200 mm)
Quill diameter	4” (102 mm)	4” (102 mm)
Quill center	M.T. 5	M.T. 5
Quill travel	7” (178 mm)	7” (178 mm)
Range of whit worth threads& No. ( )	2-72 T.P.I (45)	2-72 T.P.I (45)
Range of metric threads No.	0.2/14 (39)	0.2/14 (39)
Range of D.P. & No.( )	8-44 (21)	8-44 (21)
Range of M.P. & No. ( )	0.3-3.5 (18)	0.3-3.5 (18)
Longitudinal feed	0.0015-0.04” (0.04-1.0 mm)	0.0015-0.04” (0.04-1.0 mm)
Cross feeds	0.00075-0.02” (0.02-0.5 mm)	0.00075-0.02” (0.02-0.5 mm)
Main motor	12 ½ hp (9 kW)	12 ½ hp (9 kW)
Coolant pump	1/8 hp (0.09 kW)	1/8 hp (0.09 kW)
Length packed	100” (2500 mm)	118” (3000 mm)
Width packed	>44” (1,120 mm)	>44” (1,120 mm)
Height packed	>66” (1,670 mm)	>66” (1,670 mm)
Gross Weight	5,830lbs (2650kg)	6,600lbs (3000kg)

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

SPECIFICATIONS	AT-2180-G-TW	AT-21120-G-TW
Swing over bed	21” (533 mm)	21” (533 mm)
Swing over cross slide	14” (356 mm)	14” (356 mm)
Distance between centers	80” (2000mm)	120” (3000mm)
Spindle nose	D1-8	D1-8
Spindle bore(max. bar diameter)	3 1/16” (78.5 mm)	3 1/16” (78.5 mm)
Spindle speed	16 steps	16 steps
Spindle speed range	20 – 1,600 rpm	20 – 1,600 rpm
Ranges:	20-25-35-50-65-85-115-150-210- 280-380-500-670-900-1200-1600	20-25-35-50-65-85-115-150-210- 280-380-500-670-900-1200-1600
Length on bed	21” (537 mm)	21” (537 mm)
Width of bridge	21 3/8” (542 mm)	21 3/8” (542 mm)
Cross slide travel	11” (280 mm)	11” (280 mm)
Top slide travel	5 3/8” (137 mm)	5 3/8” (137 mm)
Number of V ways	3 each “V” ways	3 each “V” ways
Bed width	13 ½” (345 mm)	13 ½” (345 mm)
Swing in gap	31” (790 mm)	31” (790 mm)
Gap bed length from faceplate	8” (200 mm)	8” (200 mm)
Quill diameter	4” (102 mm)	4” (102 mm)
Quill center	M.T. 5	M.T. 5
Quill travel	7” (178 mm)	7” (178 mm)
Range of whit worth threads& No. ( )	2-72 T.P.I (45)	2-72 T.P.I (45)
Range of metric threads No.	0.2/14 (39)	0.2/14 (39)
Range of D.P. & No.( )	8-44 (21)	8-44 (21)
Range of M.P. & No. ( )	0.3-3.5 (18)	0.3-3.5 (18)
Longitudinal feed	0.0015-0.04” (0.04-1.0 mm)	0.0015-0.04” (0.04-1.0 mm)
Cross feeds	0.00075-0.02” (0.02-0.5 mm)	0.00075-0.02” (0.02-0.5 mm)
Main motor	12 ½ hp (9 kW)	12 ½ hp (9 kW)
Coolant pump	1/8 hp (0.09 kW)	1/8 hp (0.09 kW)
Length packed	138” (3510 mm)	178” (4520 mm)
Width packed	>44” (1,120 mm)	>44” (1,120 mm)
Height packed	>66” (1,670 mm)	>66” (1,670 mm)
Gross Weight	7,480lbs (3400kg)	9,240lbs (4200kg)

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series

Complete Product Details & Parts

Get a Quote [+]

Key Features

Videos

Item Brochure

Lease Calculator

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

Manual Lathe Heavy Duty American Turnmaster Power 5 Turret Series22"- 100" Heavy Duty Swing Lathes

All Rights Reserved © 2010 - 2011 www.lagun.com